Inboard Propeller Help


All Products Specials Contact Us Boating Help Create an account Customer Login

We Ship To Over 60 Countries, Including:

Calculate Your Shipping Now


	Site Search


	Online Store

Propellers

Inboard Propellers

Outboard Boat Propellers

Sterndrive Boat Propellers

Volvo Duo-Propellers

Ski/Wake Boat Propellers

Propeller Pullers

Propeller Cases

Nylon Bore Reducers

Propeller Help

Propeller Guide

Inboard Propeller Sizing

Product Inquiry

Zincs

Zinc Anodes

Shaft Hardware

Stainless Boat Shafts

Cutlass Bearings

Shaft Seals

Engine Coupling Guide

Engine Couplings

Shaft Logs

Packing Boxes

Marine Hardware

Underwater Hardware

Deck Hardware

Exhaust Fittings

Steering Parts

Hose and Clamps

Electronics

GPS Fishfinder/Plotters

GPS Color Plotters

Fishfinders

First Aid/AEDs

Product Catalog

Download Catalog


	Contact Us



	General Sales Department (800) 454-6960 (954) 444-6259 sales@deepblueyachtsupply.com

	Inboard Propeller Questions Use our 'Inboard Propeller' Form Or call us at: (800) 454-6960 (954) 444-6259

	Outboard Propeller Questions Use our 'Outboard Propeller' Form Or call us at: (800) 454-6960 (954) 444-6259

We gladly accept:

We ship our propellers, cutlass bearings, and zinc anodes by UPS

Inboard Propeller Question and Answers

Below is a list of questions and answers about inboard propellers that we have come across and have been asked throughout the years. Simply click on the question below to read the answer.

Can one propeller give top speed plus lots of power?

You suggest a 13" diameter x 14" pitch for my boat. Wouldn't a smaller diameter with more pitch do the same?

Will a prop change correct a disturbingly large wake?

I run on mile-high western lakes. Should I adjust prop size accordingly?

I have a right hand prop but need a left hand. Can it be changed?

How much can you change prop pitch?

What are true pitch, variable pitch and controllable pitch propellers?

Should I get my propeller dynamically balanced?

What is electrolysis, its cause, correction?

Do I use the same size wheel if I convert to a cupped-edge propeller?

What benefits does a cupped-edge wheel offer?

How can I tell if I need a left or right hand prop?

Should I use 2-, 3-, 4-, or 5-blade propellers?

What are normal slip percentages for various craft?

How close to the bottom of the boat can blade tips run and what is the required aperture clearance?

Should I use heat to install or remove my prop?

Can I put an inboard engine in my outboard hull?

My outfit doesn't have the speed I expect, though I've tried several types of prop. Why?

Will a reduction gear give me more power?

Why do hulls of the same length, beam, weight and power vary so in performance?

Can't I get more than "X" miles per gallon of gas?

A prop larger than I can swing is indicated for my boat, engine, and gear. Should I use as larger diameter as I can and add pitch to hold motor rpm down?

Won't a step-up gear increase my speed?

Can one propeller give top speed plus lots of power?

Generally no. To gain high speeds involves sizes or pitch ratios unsuited to load carrying or working conditions. Decide what is most important and select the prop accordinly, or change props with boating conditions.

Back to Question List

You suggest a 13" diameter x 14" pitch for my boat. Wouldn't a smaller diameter with more pitch do the same?

Pitch cannot be substituted for diameter. Diameter is directly related to horsepower, rpm, and speed, which indicate your requirements. If the operating conditions call for a 13" diameter, a 12" cannot be substituted without adversely affecting performance by decreasing efficiency.

Back to Question List

Will a prop change correct a disturbingly large wake?

Probably not, unless the change causes a non-planing boat to plane. Wake is directly proportional to hull displacement. Fast boats in planing position throw less wake than slow displacement boats even though the planing boat goes faster than the slow, wave-throwing hull.

Back to Question List

I run on mile-high western lakes. Should I adjust prop size accordingly?

Yes, gasoline engines lose power when operated above 3000' altitudes. A smaller pitch prop will compensate some by bringing rpm to correct operating point. Boats operated at high and low altitudes need a prop for each condition.

Back to Question List

I have a right hand rotation prop but need a left hand rotation. Can it be changed?

No. Propeller rotation cannot be changed. Turning it around won't change the rotation.

Back to Question List

How much can you change prop pitch?

Depends on the individual propeller. Average standard bronze props can be changed about 2" up or down. Remember that the metal near hubs cannot be changed. Excessive stress and strain can distort or kink blades, causing poor prop efficiency.

Back to Question List

What are true pitch, variable pitch and controllable pitch propellers?

A true pitch propeller measures constant pitch at any radius . . . a section of a true helical surface. A propeller whose pitch varies radially, that is, is not constant but increases from the hub to the tip, is a variable pitch propeller. Variable pitch propellers are used on high speed crafts and reduce cavitation which might result at such speeds. Many larger boats use variable pitch propellers to compensate for wake or varying inflow velocities which result from the depth of the immersed hull. With a controllable pitch propeller, the pitch angle of the blades can be mechanically adjusted when the boat is underway.

Back to Question List

Should I get my propeller dynamically balanced?

Most premium grade propellers are dynamically balanced at manufacture. All other propellers can be dynamically balanced but only on special order and at additional price. Such a balance is inherent proof of manufacturing perfection insofar as blade thicness, width, spacing, etc. are concerned. This inherent accuracy is not destroyed by blade damage, making it unnecessary to dynamic balance during repair. A good static balance at the repair station will suffice as the inherent accuracy of the propeller is still there.

Back to Question List

What is electrolysis, its cause, correction?

Electrolysis is the flow of electricity caused by the difference in potential of two dissimilar metals immersed in electrolyte. It acts as a plating process and one metal is eaten up and deposited on the other. Prevent harm to underwater parts by attaching sacrificial anodes (usually zinc). Replace from time to time as they deteriorate.

Back to Question List

Do I use the same size wheel if I convert to a cupped-edge propeller?

No. Diameter remains the same, but additional load placed on the engine by the "cupped edge" requires that pitch be reduced 1", or 2" in propellers above 14" diameter.

Back to Question List

What benefits does a cupped-edge wheel offer?

Cupped-edge propellers for fast boats and high rpm reduce slip, giving as much as 3 mph more speed on the average, and eliminate cavitation.

Back to Question List

How can I tell if I need a left or right hand prop?

Stand in back of boat. If shaft turns clockwise, a right hand prop is needed. Most maring motors take right hand props.

Back to Question List

Should I use 2-, 3-, 4-, or 5-blade propellers?

Excessive horsepower, direct drive and high advanced speeds indicate that propellers of high pitch-diameter ratio be employed. Generally 2-blade propellers are used. At somewhat lower advanced speeds and shaft speeds, 3-blade propellers with pitch-diameter ratios of approximately 1.0 are required for best properly efficiency. It is in the category that most pleasure boats lie. At even lower advanced speeds and shaft speeds, 4-blade propellers with pitch-diameter ratios of approximately 0.8 or less are required for optimum propeller efficiency. On large cruisers and commercial applications such as trawlers, shrimpers, tugs and workboats, 4-blade propellers are generally used. If excessive vibration is a problem, 5-blade propellers are used.

Back to Question List

What are normal slip percentages for various craft?

With propellers correctly selected for the operating conditions, the slip percentages would be as follows: racing hulls 10 to 15 percent, planing runabouts 15 to 25, planing cruisers 25 to 35, displacement cruisers 30 to 40, sailing auxiliaries 35 to 40 and work boats 40 to 80.

Back to Question List

How close to the bottom of the boat can blade tips run and what is the required aperture clearance?

The clearance between the propeller tips and the hull should be at least 1/6 to 1/7 the propeller diameter. Clearance is equally important along the forward edges of the blade where they swing in line with the deadwood and should not be less than 1/12 of the diameter.

Back to Question List

Should I use heat to install or remove my prop?

Heat should never be used to install a propeller, and, therefore, should seldom be required for removal. If a wheel puller and hammering with soft hammer on propeller and/or shaft end does not work, gentle warming with a blow torch may help. Do not use a welding torch as the quick, harsh heat will change the grain structure of the bronze, setting up internal stresses resulting in hub splitting.

Back to Question List

Can I put an inboard engine in my outboard hull?

The big question here is whether you will throw the hull out of trim with a heavy inboard mounted midships when the hull was designed to carry an outboard in back of the transom. Normally such conversions are never successful unless the hull was designed to carry the engine weight aft, or you have a V drive or a transom drive with the engine well aft.

Back to Question List

My outfit doesn't have the speed I expect, though I've tried several types of prop. Why?

Some boats do not have the power to "get over the hump" or attain planing speed. Other boats that achieve planing speeds may not have the power required to reach speeds desired. In such cases, repowering is the only answer. Power requirements are proportional to the speed cubed.

Back to Question List

Will a reduction gear give me more power?

Reduction gears in themselves do not provide power, they absorb power. They provide the means of using a greater propeller diameter, which may be more efficient. They are commonly used with high rpm engines in relatively large hulls, requiring greater blade area than can be used driving direct.

Back to Question List

Why do hulls of the same length, beam, weight and power vary so in performance?

Here the effect of an engineered design is realized. The difference between a boat designed by a qualified naval architect and one built by backyard techniques may be many miles per hour. Boat design is both a science and a skill which has evolved over many years. The designer must be cognizant of the effect of weight, weight distribution, deadrise and other hull characteristics which can affect overall performance. Otherwise, a poor performing boat results.

Back to Question List

Can't I get more than "X" miles per gallon of gas?

Don't think of miles per gallon . . . think of gallons per hour. Fuel consumption is related to the overall efficiency. Engines all use almost exactly one gallon of gas per hour for every 10 h.p. developed. For example, if you burn 15 gph, your engine puts out 150 h.p.

Back to Question List

A prop larger than I can swing is indicated for my boat, engine, and gear. Should I use as larger diameter as I can and add pitch to hold motor rpm down?

Change the gear, increasing shaft rpm, reducing prop diameter requirement, or, change shaft angle or prop aperture to accommodate correct size. If impossible, use a wide 4-blade prop for diameters 18" and up. Under 18", a 3-blade, larger in diameter than required, can be clipped to maximum usable diameter.

Back to Question List

Won't a step-up gear increase my speed?

With an extremely fast boat (step bottom hydro or drag boat), depending on your engine, a step-up gear may let you use a prop size better suited to your needs. Gears for "class" boats are usually worked out by trial and error, so stick to what has been done successfully for similar boats. Step-up gears are the opposite of reduction gears, but we still figure h.p. and rpm at the prop. With step-up gears, shaft rpm of 10,000 is not unusual in racing craft.

Back to Question List